Monthly Archives - October 2022

WATERGUARD A

TWO COMPONENT, ACRYLIC CEMENTITIOUS WATERPROOFING COATING

Many people are facing leakage and damp problems on their home terraces during the monsoon season. To come out of this problem we request you to use our WATERGUARD A.

WATERGUARD A is a prepacked two-component acrylic modified cementitious waterproofing coating. One part is liquid in white color and another is powder in grey color. After mixing both components at the site it produces a mix that is easy to use. It should be applied in 2-3 uniform coats
SALIENT FEATURES
• Prepacked easy to use water proofing coating
• Non-toxic & environmental friendly
• Excellent adhesion
• Minimum surface preparation needed
• Allows surface to breath
• Approved for potable water contact
• Economical system
APPLICATION PROCEDURE
1. Surface preparation
• Make sure all the leakage and water jet points are sealed.
• Clean the surface with wire brush and remove all loose particles.
• If any cracks are visible, repair them.
2. Mixing
• Pour the liquid polymer in the container or electrical mixer.
• Slowly add powder in it and mix continuously until the required consistency is obtained.
3. Application
• Sprinkle water on the prepared surface and allow absorption. Remove excess water from the surface.
• Stir the WATERGUARD A before applying.
• Apply uniform coat of WATERGUARD A with brush, and leave it for drying.
• Apply 2nd or subsequent coat after previous coat is dried.
• Cure the surface for 3-5 days.

WATERGUARD A is used to protect the structure against the ingress of moisture. It is used in water retaining structures like water tank, swimming pools, retaining wall, bridge walls, reservoirs, dams, dock gates etc. it is also used in and around house component like roof, terrace and balconies, basement, Lift shaft etc.

FAIRMATE WATERPLUG

A FAST SETTING PLUGGING COMPOUND FOR STOPPAGE OF RUNNING WATER

FAIRMATE WATERPLUG is a blend of cement well-graded sands and special additives in dry powder form. It requires only the addition of clean water to produce a ready-to-use, ultra-rapid setting and plugging mortar. FAIRMATE WATERPLUG is based on a mixture of cement, aggregates, and special fillers which minimises the risk of thermal cracking.

SALIENT FEATURES
• Stops running water instantly
• Sets under water
• Non shrink, non-metallic
• High structural strength
• Easy to use- simply add water
• Low exothermal minimises thermal cracking.

APPLICATION PROCEDURE

SURFACE TREATMENT
• Chisel out masonry around the hole or crack to a depth and width not less than 25 mm. Ensure that the hole is wider within the wall than at the surface. (Inverted ‘V’ Groove).
• If the water pressure is high at the area to be patched, make weep holes at the base of the wall to relieve the pressure.
• All loose material & debris should be removed.

METHOD OF USAGE

• FAIRMATE WATERPLUG should be mixed with a trowel in small quantities 1:4 by volume or 1:5 by weight (water to FAIRMATE WATERPLUG).
• Hold the mixed FAIRMATE WATERPLUG in the gloved hand until heat generation is felt and force the material in to the crack or void and hold tightly with palm of the hand for 3 minutes until FAIRMATE WATERPLUG sets.

FAIRMATE WATERPLUG is used as plugging mortar for fixing nozzles or grouting operations. It is also uses for arresting instant water seepages through dams, water tanks, basements, sunken pits, floor junctions.

PACKING & COVERAGE
FAIRMATE WATERPLUG is supplied in 1 kg, 5 Kg, 25 kg Bag.

WATERGUARD LIQUID MEMBRANE

POLYMER MODIFIED BITUMEN BASED FIBER REINFORCED FLEXIBLE, LIQUID APPLIED WATERPROOFING MEMBRANE

WATERGUARD LIQUID MEMBRANE is polymer-modified water based on bitumen, liquid applied, fiber reinforced flexible, damp-proof, and vapor-proof liquid membrane. WATERGUARD LIQUID MEMBRANE is highly resistant to aggressive soils and soluble salts providing an effective continuous barrier and protection against water Bourne damage. If a water flood test is to be run, the membrane should cure for a minimum of 7 days. Whilst WATERGUARD LIQUID MEMBRANE is resistant to frost, adhesion will be impaired if applied to frosted substrates.

SALIENT FEATURES
• free from solvents
• Very low permeability
• High elasticity, ensuring a permanently flexible barrier over a wide range of temperatures
• Thermally stable – irreversible chemical cure eliminates melting and flow at high temperature
• Can be applied to a range of substrates
• Outstanding resistance to oxidation and brittlement
• Fibers improve tensile strength and abrasion resistance

APPLICATION PROCEDURE
Surface preparation: All substrates must be sound, clean, dry, smooth and free from protrusions, voids, honey-combs and high spots. Presence of curing agents, paint and oil will impair adhesion.
Moss and lichen must be removed and area treated with proprietary fungicidal wash to kill spores and inhibit further growth. Following treatment wash area thoroughly with clean water and allow drying. Fillets must be provided at corners or sharp angles using 4:1 sand and cement mortar modified with a good quality bonding agent – FAIRCRETE SB (L).

Priming: Priming is not normally required on good quality, well prepared substrates.

Cracks: All shrinkage and non-structural cracks must be treated with not less than 1.5mm coating of WATERGUARD LIQUID MEMBRANE extending 75mm either side of the crack. Allow to cure overnight prior to general application.

Application: WATERGUARD LIQUID MEMBRANE should be applied by brush to obtain a continuous unbroken film. Two coats are required with the second coat applied at right angles after the first coat has dried. WATERGUARD LIQUID MEMBRANE must be protected from mechanical damage during subsequent construction or backfilling works. Any damage may be repaired by spot application. Application should be avoided if substrate temperatures are below 5ºC or rain is imminent.

Curing: Allow each coat to dry a minimum of 24 hours before re-coating. full cure may take after 7 days of application or more depending on temperature conditions. Cold temperatures will slow cure time, higher temperature may speed up cure time.

WATERGUARD LIQUID MEMBRANE is particularly suitable for a wide range of applications including wet areas, foundations, basements, terraces, retaining walls, bridge abutments, planters, inverted roofs and remedial repairs to felt, asphalt, concrete, fibreous cement or other roof structures when protected from exposure to direct sunlight.

PACKING & COVERAGE
WATERGUARD LIQUID MEMBRANE is supplied in 20 kg pails. It has a coverage of 1.5 – 2 m² per kg at 1mm WFT.
Coverage rate will vary with substrate condition and profile.